This QA submission should be completed by the installer on the job site. This form will require photos of all exterior and interior units. If you need support completing this form, please call Abode at 339-707-0918.
Customer Name
*
Site Address
*
Contractor Name
*
Contractor Email
*
Municipal Light Plant Electricity Provider
*
Please Select
Reading Municipal Light Department
Belmont Light
Braintree Municipal Light Department
Concord Municipal Light Plant
Middleborough Gas and Electric Department
Norwood Municipal Light Department
Wakefield Municipal Gas and Light Department
How many outdoor units were installed as part of this project?
*
Please Select
1
2
3
4
5
Image 1: Insulation must cover entire line set length (both pipes) to avoid condensation and energy loss.
Take one photo (less than 3 feet away) of each exterior line set connected to the outdoor unit clearly showing the insulated line sets.
Image 2: Once insulated, the outdoor portion of line set shall be protected with a rigid cover to avoid insulation damage.
Take one photo of each exterior line set from a distance to show the entire line set and outdoor unit. Once one photo of each unit is uploaded, you may scroll to the next question.
For each outdoor unit, please also provide one photo of the model number plate.
Take one close-up photo of each model number plate with all information clearly visible. Once one photo of each plate is uploaded, you may scroll to the next question.
Per the instructions above, provide the two required photos of the first outdoor unit.
*
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
First outdoor unit model number plate
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Per the instructions above, provide the two required photos of the SECOND outdoor unit.
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Second outdoor unit model number plate
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Per the instructions above, provide the two required photos of the THIRD outdoor unit.
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Third outdoor unit model number plate
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Per the instructions above, provide the two required photos of the FOURTH outdoor unit.
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Fourth outdoor unit model number plate
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Per the instructions above, provide the two required photos of the FIFTH outdoor unit.
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Fifth outdoor unit model number plate
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) First outdoor unit
*
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Second outdoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Third outdoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Fourth outdoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Fifth outdoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
Are all line set penetration into the home covered with PVC and rodent proof?
*
Yes
No
Are all home shell penetrations sealed with insulating sealant or spray foam?
*
Yes
No
Is the condensate line sloped downhill and away from crawlspaces, walkways, and other outdoor equipment?
*
Yes
No
Does each outdoor unit allow for free air flow and provide adequate clearance of at least 12" snow depth?
*
Yes
No
Is every outdoor unit level side-to-side and front-to-back?
*
Yes
No
Please select all applicable indoor unit types installed as part of this project.
*
Please Select
Ductless
Ducted
Combination of ductless and ducted
Are any ducts/air handlers in unconditioned spaces?
Yes
No
Are all joints and seams in ducts thoroughly sealed with mastic and all components insulated to a minimum of R-8?
Yes
No
How many indoor ductless or ducted air handler units were installed as part of this project?
*
Please Select
1
2
3
4
5
6
7
8
Indoor wall-mounted units must be installed with adequate clearance from the ceiling per the manufacturer's guidelines. In rooms with higher or vaulted ceilings, units shall be installed whenever possible so that the air discharge is no higher than 8 feet from the floor.
Take one photo of each interior head from a distance to show its positioning. Once one photo of each unit is uploaded, you may scroll to the next question.
Please upload one photo per indoor unit
*
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Second indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Third indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Fourth indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Fifth indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Sixth indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Seventh indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
(DEFUNCT) Eighth indoor unit
Upload Photo
Drag and drop files here
Choose a file
Cancel
of
If ducts and/or air handlers in unconditioned space can’t be avoided, all joints and seams in duct shall be thoroughly sealed with duct mastic and all components shall be insulated to a minimum of R-8.
Take at least one photo of each air handler unit from a distance to show its positioning. Once one photo of each unit is uploaded, you may scroll to the next question.
Please upload at least one photo of each air handler unit.
Browse Files
Drag and drop files here
Choose a file
Cancel
of
Electrical panels should be clearly labeled for all breakers associated with this install.
Are all applicable breakers clearly labeled on the electrical panel?
*
Yes
No
If thermostats are used, are they on interior walls, away from direct sunlight, appliances, or drafts?
*
Yes
No
No thermostats were installed
Has the customer been shown how to correctly use the thermostat/remote control?
*
Yes
No
Please upload a copy of the final paid invoice or contract showing the model numbers of all installed equipment (a clear photo of the invoice or contract will suffice). In order for your customer to receive a rebate, the final paid invoice is required. If your final invoice or contract does not include model numbers, please take photos of all equipment plates clearly showing the model number for final verification.
Browse Files
Drag and drop files here
Choose a file
Cancel
of
Save
Submit
Should be Empty: